NTSB/RAB-08/03 PDF Document [100 KB] |
||||||||||||||||||
|
||||||||||||||||||
SynopsisOn Saturday, July 1, 2006, about 2:53 p.m., southbound Southeastern Pennsylvania Transportation Authority (SEPTA) passenger train 1143 collided head on with standing northbound SEPTA train 1134 near Abington, Pennsylvania. The southbound train was traveling about 11 mph when it struck the northbound train. As a result of the collision, the control cab car and two passenger cars on the southbound train and the control cab car on the northbound train were derailed. Thirty-eight passengers were injured and treated on scene. Of those, 29 were transported to local hospitals, and 8 were admitted. All six crewmembers from both trains were also taken to local hospitals; three of them were admitted. Total property damage was about $179,700. The AccidentThe accident 2 occurred on single, straight track at milepost 2.8 on the Warminster Line, just south of a 3°15' curve. (See figure 1.) The weather was partly sunny, and the temperature was 83° F. At the time of the accident, both trains consisted of four electrically driven passenger cars, and each train had a lead car that was equipped with a control cab for the engineer. Each train had an engineer, a conductor, and an assistant conductor on board. |
||||||||||||||||||
 |
||||||||||||||||||
| Figure 1. Map of a portion of the
Warminster Line and the accident location.
|
||||||||||||||||||
The dispatching plan called for the two trains to meet at the Grove South Control Point, about 1.4 miles north of the collision site, with the southbound train stopping on the main track at Grove South and the northbound train entering the siding at Grove South. The southbound train did not stop on the main track at Grove South, and it did not meet any train at Grove siding prior to the collision. The southbound train engineer did not comply with a total of three wayside signal indications—approach (yellow over red over red), stop (red), and stop and proceed (red)—leading up to the collision. He also operated through and damaged the siding switch at Grove South, which was aligned for the northbound train to enter the siding. Yet, as the southbound train continued traveling between Grove South and the eventual accident site, the engineer passed three crossings and properly used the train horn at each, and he made two passenger station stops. When he saw the northbound train stopped on the track, he made an emergency brake application about 10 seconds before impact and warned passengers to brace themselves. A few minutes prior to the collision, the engineer of the northbound train passed a sequence of two signals—a clear (green) followed by a stop and proceed (red)—that concerned her. She was concerned because she had not received an approach (yellow) signal indication before the stop and proceed indication and she was operating the train on single track. The engineer stopped the train and tried calling the train dispatcher three times to confirm that the signal instructions were correct. After receiving confirmation via radio, the engineer again began to operate the train and proceed in compliance with the signal instructions. When she saw the headlights of the southbound train, the engineer of the northbound train reapplied the brakes, stopped the train just prior to the collision, and told passengers to brace themselves. The train dispatcher acknowledged a system alarm for an overrun signal, via computer mouse click, shortly after the southbound train engineer operated through the siding switch at Grove South. However, he did not take any additional action in response to the alarm. The alarm sound and screen text type were not unique, and alarms were a common occurrence for routine matters during a dispatcher’s shift. Also, although he was responsible for only one desk/dispatching area, the dispatcher was covering two desks/dispatching areas at the time of the accident because his counterpart was taking a break. InvestigationThe investigation determined that the wayside signal system and equipment were functioning properly at the time of the accident. Weather conditions did not limit visibility. No impairing substances were found during the required Federal Railroad Administration postaccident toxicological tests of all crewmembers on both trains and the dispatcher on duty when the accident occurred. The engineer of the southbound train said that the train had operated normally. SEPTA records indicated that the cars of southbound train 1143 had been inspected and tested within the required intervals. The crew had performed an air test on the train before departing Warminster. The night before the accident the mechanical department completed an inspection of the equipment. No exceptions were noted. The engineer of the southbound train was qualified to perform his duties. He had passed a physical examination that included a vision test. He had been properly trained and tested, and SEPTA had determined him to be knowledgeable of and in compliance with its operating rules. He had begun working for SEPTA as an assistant conductor in October 2004, and he had transferred to the engineer training program in 2005. The accident trip was his fifth solo trip as an engineer. The train dispatcher was qualified to perform his job duties. He had passed SEPTA’s operational tests and the recertification examination for his position. He had worked as a tower operator for 13 years, which was a position with duties similar to those of a train dispatcher. He had been in the bus service as a driver for 7 months in 2004. In July 2004, he had transferred to the dispatching center, and he had been working as a train dispatcher for about 2 years when the accident occurred. The main track movements, including movements onto and off the main track and sidings, were governed by operating rules, a wayside traffic control signal system, and a SEPTA dispatcher at SEPTA’s control center located in downtown Philadelphia, Pennsylvania. Southbound Train 1143 Engineer’s ActionsThe southbound train engineer’s descriptions of the signal aspects he had received at three locations prior to the collision did not match those recorded by the signal system or the results of postaccident testing. (See table 1 for a comparative summary of the accident signal data.) He misperceived and/or misinterpreted three different signal aspects, two of which were red, indicating the need for him to stop or stop and proceed. He also operated through and damaged the siding switch at Grove South, which had been lined for the northbound train. During the same accident trip, the engineer made appropriate station stops. He used the throttle and brakes correctly. He also used the train horn at crossings. Further, when he did see the northbound train stopped on the track and recognized the inevitability of impact, he made an emergency brake application and warned passengers. |
||||||||||||||||||
| ||||||||||||||||||
